|
|
Analyse and Optimise Production Process of Prototypes
Hamr, Tomáš ; Zatloukal, Miroslav (referee) ; Starý, Jiří (advisor)
This diploma thesis summarizes basic findings about issues of making development samples of PCB. The emphasis is especially on required quality which complies with mentioned norms. The theoretical section includes methodology for evaluating quality dismounted boards, assembling and soldering, parameters of components under different environmental circumstances. The practical part is carried out in cooperation with the department EEG in R&D Automotive Lighting Jihlava. It is dedicated to the design and the preparation of development samples where the quality is assessed according to given methodology from the theoretical part. PCB are analyzed by an X-ray, metallographic grinding and other methods. Recommendations are given and based on results for improvements.
|
|
|
Inovation of measurement equipment used for analyzing of photovoltaick cells
Otépka, Jakub ; Bača, Petr (referee) ; Vaněk, Jiří (advisor)
This bachelor thesis deals with the design of a tachometer which is used to measure and display of mechanical aperture speed of a measuring equipment for the defect analysis of solar cells using the photoluminescence method. This work is divided into three parts. The first section describes the principle of solar cells, the principle of luminescence radiation and its types. Next the defects of solar cells are analyzed. The second part discusses the theory of tachometers, the principles and methods of loading pulses. The third part is then analyzed the design and construction of the selected type tachometer.
|
|
|
Wettability of PCB Surface Finishes and Comparison of Methods
Vídeňský, Ondřej ; Přikryl, Tomáš (referee) ; Starý, Jiří (advisor)
This bachelor´s thesis deals with testing methods for surface finishe´s wettability PCB. For this tests has been designed and created testing board which contains testing coupons for testing methods. Boards have been created and covered by surface finishes by Gatema Boskovice. In this thesis electroless nickel with immersion gold (ENIG) and immersion tin have been tested. For simulation of reflow soldering have been used test methods solder indicator, solder spread test and dewetting test. Wetting balance test method has been used as simulation of wave soldering.
|
|
|
Diagnostic of photovoltaic cells by LBIV
Sládek, František ; Jandová, Kristýna (referee) ; Vaněk, Jiří (advisor)
This dissertation main point is to take up with fotovoltanic cells metering methods. Dissertation work dwells with the most common defects rising during the fotovoltanic cells manufacturing. Also, there is a diagnosis workshop proposal and realisation. Workshop uses the Light Beam Inducted Voltages (LBIV) method. By the help of this method, fotovoltanic cells structures are analised and compared to the Light Beam Inducted Current (LBIC).
|
|
|
Analysis of Defects on PCB Using Modern Optical Method
Vala, Martin ; Řezníček, Michal (referee) ; Řihák, Pavel (advisor)
This diploma thesis is focused on detecting of defects on BGA (Ball Grid Array) components using of X-ray. Defects are formed during reflow BGA components during assembly, but also later due to mechanical and thermal stress. Therefore, there is an overview of defects and methods of diagnosis of BGA packages eg .: modern X-ray defect detection or micro sections. There is disclosed a device NORDSON DAGE XD7600NT its operation and setup. The device enables advanced methods of scanning called X-plane. For creating 3D models used reconstructive software called CERA, which uses raw data from the method of X-Plane.
|
|
|
Set possible causes for capacity loss of capacitors
Fabiánek, Marcel ; Špinka, Jiří (referee) ; Starý, Jiří (advisor)
This thesis deals with formation of defects on through-hole capacitors. Process of wave soldering and its steps are described in the first part. The listing and description of possilble defects caused by wave soldering is followed after the first part. There are several sources of potential causes of capacity loss and a separate chapter to these causes. The last part contains a proposal of testing individual potencional causes. Their purpose is to reveal the root causes of formation of the defects and then the practical solution is described.
|
|
|
Microscopic analysis of silicon solar cells defects
Brukner, Jakub ; Solčanský, Marek (referee) ; Stojan, Radek (advisor)
This thesis deals with detection of defects solar cells using method electroluminescent, electron microscope and subsequent 3D modeling of areas with defects and structure of the solar cell. In the text are describe basic methods for detection of defects appearing in solar cells. Also some basic defects which can be made during manufacture are there describe. For better orientation the basic principle of functionality and manufacturing process is included.
|
|
|
MOISTENING OF COMPONENT MATERIALS AND SPEED OF DEHUMIDIFICATION
Pospíšil, Tomáš ; Tomáš, Bžoněk (referee) ; Starý, Jiří (advisor)
This bachelor thesis deals with process associated with moisture in electrotechnics. The bachelor thesis is focused on the components and basic materials that are sensitive to moisture and defects caused by moisture in the reflow soldering process. The theoretical part describes the principles of measuring humidity and sorts of absorption. Furthermore this work described the basic classification and defects in components, base materials and packaging material sensitive to moisture and selection of standards dealing with this issue. Another theoretical part is focused on the manipulation with components and materials sensitive to moisture. The practical part deals with the methodology and practical measurement of moisture soaking in the components and materials with respect to their level of sensitivity to moisture. The following part is focused on the methodology of drying, practical measurement of drying and comparing two drying cabinets.
|
|
|
Synthesis of electromagnetic bandgap structures
Šedý, Michal ; Kovács, Peter (referee) ; Raida, Zbyněk (advisor)
In microwave frequency band, the planar technology is mainly used to fabricate electronic circuits. Propagation of surface waves belongs to the significant problem of this technology. Surface waves can cause unwanted coupling among particular parts of the structure and can degrade its parameters. The problem can be solved using an electromagnetic band gap structure (EBG). These periodic structures are able to suppress surface waves in different frequency bands. This thesis is focused on the modeling of these structures in the program COMSOL Multiphysics.
|
|
| |
guest ::
